Photo Gallery

 1. Chassis:
2wd 11.5-13.5” wheelbase.
Rear Motor and Mid Motor Allowed
No 4wd or 4wd to 2wd conversions.

2. Motor/ Speed Control:
Motor
Any 13.5t commonly available
ESC
Any commonly available ESC with blinky mode
** No added ESC timing is allow**
** ESC must show a blinking light to show no timing is added **

3. Battery:
Any commercially available 2s (in store or online) Lithium-Ion Polymer (LiPo), Graphene, or LiPo HV Battery. Must have a plug or bullet connectors (no hard wiring)
Single battery pack Only! No multi packs plugged in parallel.
3.1 Voltage:
A Maximum of 8.44 Volts will be allowed.

4. Tires:
DRY TIRE ONLY
Front: Any commercially available (in store or online) rubber with foam insert type.
No O-Ring type. Min size 68mm or 2.68 inches
Rear: Any commercially available (in store or online) rubber with foam insert type.
Treaded and slicks acceptable.
4.1 Foam Insert
Foam insert is not required in front or rear tires but maybe ran.
4.2 Prep:
** No Prep of tires is allowed at the race track. **
No prep residue from tire warmers
Cleaning and heating between rounds is ok
4.3 Burn Out:
A burn out is optional but highly encouraged.
When Burnouts are being done by racers they must be done on the race surface behind the starting line. A burnout box will be defined by the race director.

5. Shocks:
Must have four shocks each controlling a wheel as intended by typical manufacturers. (Connected and operating hinge pin arms at all four corners of the car.)
Shocks must have movement visible and acceptable by the race director.

6. Transmission:
Car must use a 3-5 gear transmission (gear box)
Belts or link conversions not allowed.

7. Weight:
Cars ready to run must meet a minimum weight of 4.54lbs, 72.6oz, or 2060 grams

8. Wheelie bar:
No Wheelie Bar is allowed

9. Body:
Must be a realistic looking drag car style body.
No Pro Mods Allowed. Please refer to non approved body list.
Body must cover wheels (i.e. no buggies)
Wheel wells must be cut along the cut line. Where a cut line is not present the body must be cut exposing the entire tire (rubber) at all four corners while car is at ride height.
9.1 Rear Body Cutouts:
Entire rear of body must remain in place.
**Must retain the Original rear side quarter fenders, trunk lid and/or pickup bed.**
9.1.2 Front Body Trimming
Front of the body must retain the entire front grill and cannot be cut any higher than the factory cut lines
**Making the body an aggressive wedge is not allowed**
**Body must be cut to factory cut lines**
9.2 Body Holes:
Up to four (4) holes for mounting, no larger than ½” at any location on the body are allowed. Window cut outs Not allowed.
Extra holes will need to be covered in tape or stickers if body has been remounted.
9.3 Spoilers and Splitters:
No added wings, spoilers or splitters allowed
Rear spoilers supplied with a body are considered legal for that body in their intended design.

***This is the list of NON APPROVED bodies for 13.5t ***
Proline/Protoform:
Corvette C7, Nissan GTR, Super J
JConcepts:
1968 Pontiac Firebird, Pontiac Firebird Pro, Cadillac ATS-V, Chevy S-10
Shark:
Psycho, MoPowr, Street Fighter, Hooligan, Freak Show, The Stinger, Boss, Cherry Bomb, Plum Crazy, Zero Drag Racer – Camry, Game Changer, Killer V
Racer RC:
Mach 22, LS-22, Supa-22
Bitty Design
ZL21

1. Chassis:
2wd 12-13.5” wheelbase.
Rear Motor and Mid Motor Allowed
No 4wd or 4wd to 2wd conversions.

2. Motor / Speed Control:
Any commonly over the counter 1/10 RC car motor.
Maximum Allowed can size is 550.
** Full Speed Control Timing and Tuning Allowed.
** No "Assist" receivers or gyros, or any driving assist items allowed. No AVC Receivers. No TSM receivers.

3. Battery:
Any commercially available 2s (in store or online) Lithium-Ion Polymer (LiPo), Graphene, or LiPo HV Battery.
Must have a plug or bullet connectors (no hard wiring)
Single battery pack Only! No multi packs plugged in parallel.
A hard case is not required.
A 3D printed case for your pack is encouraged.
3.1 Voltage:
A Maximum of 8.44 Volts will be allowed.

4. Tires:
Front: Any commercially available (in store or online) rubber with foam insert type.
No O-Ring type. Min size 68mm or 2.68 inches
Rear: Any commercially available (in store or online) rubber with foam insert type.
Treaded and slicks acceptable.
4.1 Foam Insert
Foam insert is not required in front or rear tires but maybe ran.
4.2 Prep:
Use of tire prep is allowed.
4.3 Burn Out:
A burn out is not required. But we highly encourage it!

5. Shocks:
Must have four shocks each controlling a wheel as intended by typical manufacturers. (Connected and operating hinge pin arms at all four corners of the car.)
Shocks must have movement visible and acceptable by the race director.

6. Transmission:
Car must use a 3-5 gear transmission (gear box)
Belts or link conversions not allowed.

7. Weight:
Cars ready to run must meet a minimum weight of 4.54lbs, 72.6oz, or 2060 grams

8. Wheelie bar:
No item may extend more than 14” from the rear dogbone including any wheelie bar parts or wheels.
8.1 Wheelie Bar Wheels:
Maximum of 1.5” tall wheels.

9. Body:
Must be a realistic looking drag car style body.
Pro Mods Allowed.
Body must cover wheels (i.e. no buggies)
Wheel well must be cut exposing a minimum of 1/2 the wheel.
9.1 Rear Body Cutouts:
The rear section of the body (valance/bumper panel) may be removed to mount a spoiler.
**Must retain the Original rear side quarter fenders, trunk lid and/or pickup bed.**
9.2 Body Holes:
Up to four (4) holes for mounting, no larger than ½” at any location on the body are allowed. Window cut outs Not allowed.
Extra holes will need to be covered in tape or stickers of body has been remounted.
9.3 Spoilers and Splitters:
Rear wings, spoilers, and side dams may extend off the body’s rear deck a max of 3 inches and cannot extend taller than parallel to the roofline.
Rear spoilers supplied with a body are considered legal for that body in their intended design.
Nose splitters may extend a max of 1/2” from the edge of the body.

10 Time
Outlaw2 is a 2.5 second index class. The car must not go faster then 2.5 second (GNSS or timing, what ever is avalible at the event)

10.1
Racers must show gnss times to race control after every run

1. Chassis:
2wd 12-13.5” wheelbase.
Rear Motor and Mid Motor Allowed
No 4wd or 4wd to 2wd conversions.

2. Motor / Speed Control:
Any commonly over the counter 1/10 RC car motor.
Maximum Allowed can size is 550.
** Full Speed Control Timing and Tuning Allowed.
** No "Assist" receivers or gyros, or any driving assist items allowed. No AVC Receivers. No TSM receivers.

3. Battery:
Any commercially available 2s (in store or online) Lithium-Ion Polymer (LiPo), Graphene, or LiPo HV Battery.
Must have a plug or bullet connectors (no hard wiring)
Single battery pack Only! No multi packs plugged in parallel.
A hard case is not required.
A 3D printed case for your pack is encouraged.
3.1 Voltage:
A Maximum of 8.44 Volts will be allowed.

4. Tires:
Front: Any commercially available (in store or online) rubber with foam insert type.
No O-Ring type. Min size 68mm or 2.68 inches
Rear: Any commercially available (in store or online) rubber with foam insert type.
Treaded and slicks acceptable.
4.1 Foam Insert
Foam insert is not required in front or rear tires but maybe ran.
4.2 Prep:
Use of tire prep is allowed.
4.3 Burn Out:
A burn out is not required. But we highly encourage it!

5. Shocks:
Must have four shocks each controlling a wheel as intended by typical manufacturers. (Connected and operating hinge pin arms at all four corners of the car.)
Shocks must have movement visible and acceptable by the race director.

6. Transmission:
Car must use a 3-5 gear transmission (gear box)
Belts or link conversions not allowed.

7. Weight:
Cars ready to run must meet a minimum weight of 4.54lbs, 72.6oz, or 2060 grams

8. Wheelie bar:
No item may extend more than 14” from the rear dogbone including any wheelie bar parts or wheels.
8.1 Wheelie Bar Wheels:
Maximum of 1.5” tall wheels.

9. Body:
Must be a realistic looking drag car style body.
Body must cover wheels (i.e. no buggies)
Wheel well must be cut exposing a minimum of 1/2 the wheel.
9.1 Rear Body Cutouts:
The rear section of the body (valance/bumper panel) may be removed to mount a spoiler.
9.2 Body Holes:
Up to four (4) holes for mounting, no larger than ½” at any location on the body are allowed. Window cut outs Not allowed.
Extra holes will need to be covered in tape or stickers of body has been remounted.
9.3 Spoilers and Splitters:
Rear wings, spoilers, and side dams may extend off the body’s rear deck a max of 3 inches and cannot extend taller than parallel to the roofline.
Rear spoilers supplied with a body are considered legal for that body in their intended design.
Nose splitters may extend a max of 1/2” from the edge of the body.